Top 10 arduino nano micro usb for 2018
If you looking for arduino nano micro usb then you are right place. We are searching for the best arduino nano micro usb on the market and analyze these products to provide you the best choice.
1. Emakefun for Arduino Nano V3.0, Micro USB Nano Board ATmega328P 5V 16M Micro-Controller Board (5PCS)
Feature
Emakefun Nano used common Micro-USB instead of Mini-USB.6-20V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.Emakefun Nano is a small, complete, breadboard-friendly andhigh qualityboard based on the Atmega328P-AU MCU.Support ISP download, USB download and USB Power
Emakefun Nano is using the chips ATmega328P and CH340, not FT232 as official Arduino,so pls.use the driver from this link:https://github.com/emakefun/emakefun-nano-kit
We used high quality PCB original material and Immersion Gold Technology to make sure every board has smooth edge and more reliable quality to make sure every board has smooth edge and more reliable quality
Nano's got the breadboard-ability of the Boarduino and the micro+USB with smaller footprint than either, so users have more breadboard space. It's got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND on one top, power and ground on the other)
Description
Specification: CH340G Replace FT232RL. Operating Voltage(logic level): 5V. 8 analog inputs ports:A0 ~ A7. 14 Digital input / output ports:TX,RX,D2 ~ D13. 6 PWM ports:D3, D5, D6, D9, D10, D11. 1 pairs of TTL level serial transceiver ports RX / TX. Support USB download and Power. Support for external 5V ~ 12V DC power supply. Support power supply by 9V battery. Support ISP download. Package including: 5 x Arduino Nano V3.0 with ATMEGA328P Module2. ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 (Nano x 3 Without Cable)
Feature
You could download the driver of Elegoo Nano V3.0 at: http://bit.ly/2jKlJMOThe Nano is using the chips ATmega328P and CH340, not FT232 as official Arduino, so pls. use the driver from above link.
It is a smallest, complete, and breadboard friendly board. It has everything that Diecimila/Duemilanove has (electrically) with more analog input pins and onboard +5V AREF jumper.
Nano's got the breadboard-ability of the Boarduino and the Mini+USB with smaller footprint than either, so users have more breadboard space. It's got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND on one top, power and ground on the other).
The Nano can be powered via the Mini-B USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.
Description
The Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.x). It has more or less the same functionality of the Arduino/Genuino UNO, but in a different package. It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard one.You could download the driver of Elegoo Nano V3.0 at: http://bit.ly/2pMF4in
Technical specs
Microcontroller: ATmega328
Architecture: AVR
Operating Voltage: 5 V
Flash Memory: 32 KB of which 2 KB used by bootloader
SRAM: 2 KB
Clock Speed: 16 MHz
Analog I/O Pins: 8
EEPROM: 1 KB
DC Current per I/O Pins: 40 mA (I/O Pins)
Input Voltage: 7-12 V
Digital I/O Pins: 22
PWM Output: 6
Power Consumption: 19 mA
PCB Size: 18 x 45 mm
Weight: 7 g
Package Include :
3 X Nano Board
ATTENTION:
We dont have USB cables in this kit and you will need to buy a mini USB cable to use this NANO board.
3. Keywish For Arduino Nano V3.0, ATmega328P Moudle Nano Board CH340 With USB Cable Compatible With Arduino Nano V3.0 (5pcs Nano Board & 1pcs Cable)
Feature
CH340G Replace FT232RL,so pls. use the driver from this link: https://github.com/keywish/arduino-nano-kitThe Nano can be powered via the Mini-B USB connection, 6-20V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.
The Arduino Nano is a compact board similar to the UNO.The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328P (Arduino Nano 3.x). It has more or less the same functionality of the Arduino Duemilanove, but in a different package. It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard one.
The Arduino Nano can be powered via the Mini-B USB connection, 6-20V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.
Quick-responding technical support for free.
Description
Specification: -CH340G Replace FT232RL. -Operating Voltage(logic level): 5V. -8 analog inputs ports:A0 ~ A7. -14 Digital input / output ports:TX,RX,D2 ~ D13. -6 PWM ports:D3, D5, D6, D9, D10, D11. -1 pairs of TTL level serial transceiver ports RX / TX. -Support USB download and Power. -Support for external 5V ~ 12V DC power supply. -Support power supply by 9V battery. -Support ISP download. Package including: 3 x Arduino Nano V3.0 with 1 x USB Cable4. Emakefun for Arduino Nano V3.0, Nano board ATmega328P 5V 16M Micro-controller board with USB cable (Pre-soldered Nano 5pcs)
Feature
CH340G Replace FT232RL,so pls. use the driver from this link:https://github.com/emakefun/emakefun-nano-kitTheUpgradedEmakefun Nano is a small, complete, breadboard-friendly andhigh qualityboard based on the Atmega328P-AU MCU.Adopting Immersion Gold Technology. Support ISP download, USB download and USB Power
No Soldering needed.TheUpgradedEmakefun Nano improved the design of PCB to solve the issue that the pins of Nano can't fit to breadboard perfectly. When you use our upgraded Nano, you will find the Pins arealigned nicely with the holes of breadborad
Nano's got the breadboard-ability of the Boarduino and the Mini+USB with smaller footprint than either, so users have more breadboard space. We use high quality PCB original material and iproved produce technology to make sure every board has smooth edge and more reliable quality
It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard one, 6-20V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27).
Description
Specification: CH340G Replace FT232RL. Operating Voltage(logic level): 5V. 8 analog inputs ports:A0 ~ A7. 14 Digital input / output ports:TX,RX,D2 ~ D13. 6 PWM ports:D3, D5, D6, D9, D10, D11. 1 pairs of TTL level serial transceiver ports RX / TX. Support USB download and Power. Support for external 5V ~ 12V DC power supply. Support power supply by 9V battery. Support ISP download. Package including: 5 x Arduino Nano V3.0 with ATMEGA328P Module (welded) 1 x USB Cable5. Gikfun USB Nano V3.0 ATmega328 CH340G 5V 16M Micro-controller board For Arduino (Pack of 3pcs) EK1620x3
Feature
Operating Voltage(logic level):5V,Support USB download and PowerPlease wear anti-static gloves or bracelet when operate electronic products.Please keep it in anti-static bag when not use it. Please keep it out of reach of children.
Don't use aged usb cable or aged circuit board to connect Nano V3.0 Board.Pull down the usb from computer when no need to upload and download procedures.
Suit for people above 18 year's old with 1 year electronic diy experience.Or use it under the guidance of electronic specializer
The product is used for learning and test Code.It's Prohibited for any other purpose.
Description
Specifications:Product Dimensions:4.2x1.7x0.5cm
CH340G REPLACE FT232RL
Operating Voltage(logic level):5V
8 analog inputs ports:A0 ~ A7
14 Digital input / output ports:TX,RX,D2 ~ D13
6 PWM ports:D3, D5, D6, D9, D10, D11
1 pairs of TTL level serial transceiver ports RX / TX
Using Atmel Atmega328P-AU MCU
Support USB download and Power
Support for external 5V ~ 12V DC power supply
Support power supply by 9V battery
Simple Operation:
1.Down CH340G Driver
CH340G Driver Download link : http://www.5v.ru/ch340g.htm
IDE of arduino Download link : http://arduino.cc/en/Main/Software
The driver which works for MAC User "www.wch.cn/downfile/178"
2.Plug in the Nano development board,the driver will install automatically
Package Included:
3Packs USB Nano V3.0 ATmega328 CH340G 5V 16M Micro-controller board
Warranty:
45 days money-back and 12-month, worry-free Guarantee!
Gikfun USB Nano V3.0 Micro-controller board is totally safe product which has been certified by USA Federal Communications.
Notes:
1.Don't use aged usb cable or aged circuit board to connect Nano V3.0 Board
2.Pull down the usb from computer when no need to upload and download procedures
Warning:
1.The product is used for learning and test Code.
It's Prohibited for any other purpose.
2.Suit for people above 18 year's old with 1 year electronic diy experience.
Or use it correctly under the guidance of electronic specializer.
3.Please wear anti-static gloves or bracelet when operate electronic products.
Please keep it in anti-static bag when not use it.
Please keep it out of reach of children.
6. diymore 2PCS CH340 TTL Micro USB NANO V 3.0 Atmega328 Atmega328P Pro Mini Strong Board Microcontroller Module Replace FT232RL for Arduino
Feature
It is based on for Arduino NANO V3.0 design.The NANO strong is an for Arduino compatible board.
SPI, COM and IIC bus breakout make bus connect easier.
The NANO strong is a microcontroller board based on the ATmega328.
Some visible improvement on hardware make more flexible and easier to use.
Description
It has 14 digital input / output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or battery to get started.
The NANO strong has an increased pin header spacing of 2.54mm and leads to all I / Os and VCC / GND.
We can conveniently connect various modules via DuPont wire, and our engineers love to use it for some applications.
In addition:
ForArduino is an open-source physical computing platform based on a simple i / o board and a development environment that implements the Processing / Wiring language.
ForArduino can be used to develop stand-alone interactive objects or can be connected to software on your computer ( eg Flash, Processing, MaxMSP).
The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux).
The output of red pins is 5V. If the current does not reach 500ma, you'd better connect the external power supply for the motor.
Package Inclueded:
2Pcs CH340 CH340G TTL Micro USB NANO V 3.0 Atmega328 Atmega328P Pro Mini Strong Board
7. Keywish 3pcs Pro Micro ATmega32U4 5V/16MHz Development Board With 2 Row Pin Header for Arduino Leonardo Replace ATmega328 Arduino Pro Mini
Feature
The Pro Micro is based on the ATmega32U4 microcontroller,it running at 5V/16MHzSupported by Arduino IDE v1.0.1
There are 4 channels of 10-bit ADC, 5 PWM pins, 12 DIOs as well as hardware serial connections RX and TX on Pro Micro
The ATmega32U4 chip on the Pro Micro board comes preprogrammed with a bootloader that allows you to upload new code to it without the use of an external hardware programmer
The PRO Micro board can be powered via the micro USB connection or with an external power supply
Description
Note: When you open the Arduino IDE software, pls go to the tool and choose the board "Arduino Leonardo"Description:1. The Pro Micro is similar to the Pro mini except with a ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connectivity on board and do away with bulky external USB interface.2. This tiny little board does all of the neat-o Arduino tricks that you're familiar with: 4 channels of 10-bit ADC, 5 PWM pins, 12 DIOs as well as hardware serial connections Rx and Tx. Running at 16MHz and 5V, this board will remind you a lot of your other favorite Arduino-compatible boards but this little guy can go just about anywhere. If you're supplying unregulated power to the board, be sure to connect to the "RAW" pin on not VCC.Features:ATmega32U4 running at 5V/16MHzSupported by Arduino IDE v1.0.1On-Board Micro-USB connector for programming4 x 10-bit ADC pins, 12 x Digital I/OsRx and Tx Hardware Serial ConnectionsPackage included:3* Pro Micro ATmega32U4 5V/16MHz Development Board8. HiLetgo 3pcs Pro Micro Atmega32U4 5V 16MHz Bootloadered IDE Micro USB Pro Micro Development Board Microcontroller Compatible to Arduino Pro Micro Serial Connection with Pin Header
Feature
ATmega32U4 running at 5V/16MHzSupported by Arduino IDE v1.0.1
On-Board Micro-USB connector for programming
4 x 10-bit ADC pins, 12 x Digital I/Os
Rx and Tx Hardware Serial Connections
Description
Description:1. The Pro Micro is similar to the Pro mini except with a ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connectivity on board and do away with bulky external USB interface.
2. This tiny little board does all of the neat-o Arduino tricks that you're familiar with: 4 channels of 10-bit ADC, 5 PWM pins, 12 DIOs as well as hardware serial connections Rx and Tx. Running at 16MHz and 5V, this board will remind you a lot of your other favorite Arduino-compatible boards but this little guy can go just about anywhere. If you're supplying unregulated power to the board, be sure to connect to the "RAW" pin on not VCC.
Features:
ATmega32U4 running at 5V/16MHz
Supported by Arduino IDE v1.0.1
On-Board Micro-USB connector for programming
4 x 10-bit ADC pins, 12 x Digital I/Os
Rx and Tx Hardware Serial Connections
Note: When you open the Arduino IDE software, pls go to the tool and choose the board "Arduino Leonardo"
Package included:
3* Pro Micro ATmega32U4 5V/16MHz Development Board
9. Micro USB FTDI Basic Breakout Module for Arduino 3.3V/5V
Feature
3.3V/5V adjustableDescription
The newest revision of our FTDI Basic with micro USB port, which use a 6-pin header on the bottom, smaller and more compact. Functionality has remained the same. This is a basic breakout board for the FTDI FT232RL USB to serial IC.The pinout of this board matches the FTDI cable to work with Arduino boards.
It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector.
The pins labeled BLK and GRN correspond to the colored wires on the FTDI cable. The black wire on the FTDI cable is GND, green is CTS. Use these BLK and GRN pins to align the FTDI basic board with your Arduino target.
This board has TX and RX LEDs that make it a bit better to use over the FTDI cable. You can actually see serial traffic on the LEDs to verify if the board is working.
This board was designed to decrease the cost of Arduino development and increase ease of use (the auto-reset feature rocks!).
10. Aideepen 3.3V 8MHz Pro Micro Atmega32U4-AU Module Bootloadered Micro USB Controller Development Board for Arduino Nano
Feature
Atmega32U4-AU running at 3.3V/8MHzOn-board Micro USB connector for programming
Supported under Arduino IDE v1.0.1
The Pro Micro is similar to the Pro Mini except with an ATmega32U4 on board
Rx and Tx Hardware Serial Connections
Description
Package Included:1 x 3.3V 8MHz Pro Micro Atmega32U4-AU Board
Recent Comments