The 10 best boiler ignitor for 2018
Finding the best boiler ignitor suitable for your needs isnt easy. With hundreds of choices can distract you. Knowing whats bad and whats good can be something of a minefield. In this article, weve done the hard work for you.
1. Robertshaw 41-406 Hot Surface Ignitor
Feature
Made From High-Purity Recrystallized Silicon Carbide. (Crystartm) Which Combines Physical And Thermal Strength With Stable Electrical PropertiesDesigned To Reach Ignition Temperature(S) Within 17 Seconds
Have 18-gauge nickels chrome lead wires embedded and metalized in place for maximum holding strength and electrical conductivity
Manufactured with lead wires enclosed in a special high-temperature fiberglass insulation providing electrical protection
Operate at 120V AC. Some modules are rated for 208/240V input, however, the voltage to the ignitor is stepped down to 120V AC
Description
The Robertshaw Carbide Series hot surface ignitors deliver dependable ignition in heating systems of every description: furnaces, boilers, rooftop heaters, Infrared burners, unit heaters, water heaters, and many other types of HVAC equipment. Packaged with special mounting adaptors. made in United States. Manufactured by Robertshaw controls company.2. Silicon Nitride Igniter Kit, Lot of 1
Feature
Low energy consumptionUsed in furnaces, boilers & water heaters
MFG# SSN2000
Description
SSN2000 SILICONE NITRIDE UNIVERSAL IGNITER KIT3. Buderus 7099006 Hot Surface Ignitor
Feature
For use with Buderus GB142 series boilersDescription
Buderus 7099006 Hot Surface Ignitor4. ITT McDonnell Miller RB24 RB-24 Series Low Water Cut-Offs - Electronic for Hot Water Boilers
Description
Residential low water cut-off boiler control5. Teledyne Laars R0317200 Pool Heater Parts Ignitor
Feature
Hot surface ignitor for Teledyne Laars/Jandy Lite LLD and Lite 2 LD pool heatersFits Zodiac Jandy Lite2LD pool and spa heater models 125, 175, 250, 325 and 400
Description
Teledyne Laars R0312700 ignitor for Lite 2 LD pool heaters models 125, 175, 250, 325 and 400. The igniter is a "glow bar" type silicon carbide unit. It is energized whenever there is a call for heat and the red "IGNITER" light on the boiler control is lit. After the igniter is switched off and the boiler continues to run, the igniter functions as a flame sensor for the boiler control. If the ignitor fails and must be replaced, always install a new igniter gasket with the replacement igniter CAUTION: Ignitor gets hot.6. Emerson H150 Universal Hot Surface Ignitor
Feature
Universal compatibility - replaces 150 common igniters covering almost 90% of applicationsFor gas-fired forced-air furnaces, water heaters and boilers
Features universal mounting bracket to eliminate the need for multiple brackets
Features large ignition area for easy installation and consistent ignition
Durable, nitride construction for most applications
Description
The White-Rodgers H150 hot surface igniter features universal compatibility, replacing 150 common igniters for almost 90% of applications. The large ignition surface area and universal mounting bracket simplify mounting for consistent ignition.7. Robertshaw 41-405 Hot Surface Ignitor
Feature
Made From High-Purity Recrystallized Silicon Carbide. (Crystartm) Which Combines Physical And Thermal Strength With Stable Electrical PropertiesDesigned To Reach Ignition Temperature(S) Within 17 Seconds
Have 18-gauge nickels chrome lead wires embedded and metalized in place for maximum holding strength and electrical conductivity
Manufactured with lead wires enclosed in a special high-temperature fiberglass insulation providing electrical protection
Operate at 120V AC. Some modules are rated for 208/240V input, however, the voltage to the ignitor is stepped down to 120V AC
Description
The Robertshaw Carbide Series hot surface ignitors deliver dependable ignition in heating systems of every description: furnaces, boilers, rooftop heaters, Infrared burners, unit heaters, water heaters, and many other types of HVAC equipment. Packaged with special mounting adaptors. made in United States. Manufactured by Robertshaw controls company.8. Ignitor Gasket for Alpine Boilers (Pack of 4)
Description
Ignitor Gasket for Alpine Boilers (Pack of 4)9. Hot Surface Ignitor for GB142 Boilers
Description
Hot Surface Ignitor for GB142 Boilers10. Ignitor, Cable & Gasket (for Solo 60-399, PE110 Trimax Boilers only)
Recent Comments